DIY Exhaust grounding kit

**JUNKee Garage - DO IT YOURSELF EngineerinG**

now offers specialized earthing straps to properly ground your cars, trucks and SUVs exhaust system to the chassis. Based on research and development of the Hyper Ground System, the new exhaust earth is designed to maximize exhaust efficiency. The exhaust and muffler ground wire can be install to your cars, trucks and SUVs stock exhaust system, or aftermarket performance cat back and universal muffler system. Universal Hot Earth Exhaust Ground System for cars, trucks and SUVs Features:

* Increase torque response
* Reduced static electricity in exhaust
* Reduced vibration noise from exhaust

-The Theory Behind the Product:
There's a lot of static electric will be created once your started your engine by the friction between the exhaust gas and the exhaust pipe inner surface which eventually will become a resistance for your exhaust gas flow.With the grounding strap, the static electric will ground it away from your exhaust system so you'll experience SMOOTHER exhaust gas flow which means Better Throttle Response!! And nevertheless,for some car with poorer chassis grounding your O2 Sensor will be benefit too with this simple move.


FAQ
1) where & how to install ?
ANS: example of the installation. 1 strap install around the catalyst converter, another strap install around the muffler is recommended.

We're on TWITTER now ~~!!

DIY tutorial: Smoked it !!!

place can be apply: head lamp, tail lamp, side marker, etc.


Ingredients:
1.spray canned for plastic material (colour: smoke)
2.masking tape
3.old newspaper


WARNING!
Please take note, make sure you are using the spray canned that can be apply on plastic material. The spray canned I'm using on this tutorial was TAMIYA TS-71 spray canned (colour: smoke).

______________________________________________________________

1. prepare the staff you want to smoke, and clean the surface of it. make sure the surface was clean and oil less.


2.using masking tape & newspaper to cover up the other place that you not going to spray....


3.after above step done, you can start to SMOKED it !!
*1 - 2 layers will b thin smoked ...4 layers will be heavy smoked.


4. FINALE, unmask.... DONE.... !!!


PROUDLY PRESENT by:
HISHA

DIY tutorial: Thermal Wrapping

Ingredients:
1.Thermal Wrap (30meters for whole exhaust system,15meters for header or turbo manifold)
2.Clips (the more clips the more secure n firm your wrapping will be)


Tools:
1.Long nose plier
2.Gloves


Advantages:
Exhaust
1.Bring down temperature in your Engine Bay
2.Increase exhaust temperature for faster air flow velocity
3.Nicer n Tidy engine bay's looks
AIr cond. Piping
1.Minimize the engine heat interference with the air con piping which coolant flowing in it.Consistency of air con temperature

Intake Piping
1.Cooler intake air = Engine perform better and more constant.

WARNING!
This is a fibreglass based thermal wrap,It will cause itchyness when in contact with human skin.Gloves,Long sleeves and long pant are advised to be worn during the process.
_____________________________________________________________

1.Place one end of your thermal wrap perpendicular to the piping you want and hold it.


2.Wrap around it and make a 30degree turning


3.Let every wrapping overlap it by half of the thermalwrap's width. The 2nd Pic show you a wrong example without overlapping it.Yes it will save u some of the stuff but the finish product won't last long and it doesn't function cos there's a leak for heat dissipation.



4.Put your clips in...pull n Fully Tighten it (moderately pulling force cos the edge of the clip is kinda sharp)


5.Now take out ur long nose plier and really make sure ur clips is FULLY tighten!


6.Cut the the extra left over material,fold it back and fold again so that u can insert it back to the clips holder itself....after folded u may wanna hammer it abit to reassure that it's secure properly


Basically i've oredi briefly the necessary skill for this DIY...the rest of the wrapping just apply the similiar technic.Oh ya...you wanna ask me how many clips to use huh?yaya....i'll tell you more clips = more secure.But fren...agak agak lah.

Finally!


I post this DIY doesn't mean i'm a pro in it...any question or doubt just post here,let's discuss!Enjoy The fun of Builiding ur own machine!

PROUDLY PRESENT by
MJ